What is EEPROM ?Learn MPS Technology on mps-technology.net. What is EEPROM ? article will help answer your questions on MPS Technology.We at mps-technology.net specialize in MPS Technology. MPS Technology at mps-technology.net provides the most up to date news and articles. If you have questions please do not hesitate to contact us.
When the monitor is turn on again, the stored settings are used to set up the monitor for operation. What are the symptoms if the MONITOR or TV's EEPROM data is corrupted or damaged? ' No high voltage (no display). ' Horizontal or vertical frequencies run. ' Cannot save (store) current setting. ' Certain control functions like sound, brightness and contrast control does not functioning. ' On Screen Display (OSD) does not function or the OSD have a corrupted display. ' High voltage shut down (EEPROM set the horizontal frequency way too low or twice the line frequency perhaps leading to failure of the horizontal output transistor (HOT)). What is an EEPROM programmer or copier? EEPROM seldom fail, they just lose or have their memory (data) corrupted may be due to high voltage and static discharge from a monitor. Article: EEPROM stands for Electrical Erasable Programmable Read Only Memory and also referred to as E²PROM. As the name suggest, an EEPROM can be both erased and programmed with electrical pulses. Since it can be both electrically written into and electrically erased, the EEPROM can be rapidly programmed and erased in crown for reprogramming without removing them from the total environment board. EEPROM is also a non-volatile memory being when power is turned off the stored data in the EEPROM will not be erased or intact. New EEPROM have no data in it and usually have to program with a programmer ere it can be use. Information stored in this type of memory can be retained for many years without a steady power supply. What is the function of EEPROM? EEPROMs are used to store user programmable information such as: - VCR programming information CD programming information Digital satellite receiver control data User information on various consumer products EEPROM in monitor performs two functions: - When a monitor is switch on it will copies all data or information from the EEPROM to the microprocessor. For example, the EEPROM will let the microprocessor know the frequencies at which the monitor is going to operate. The EEPROM is used to store the current settings of the monitor. The settings of the monitor will not be erased even when the monitor is turned off. Anytime a tit for tat is made in the monitor settings, the microprocessor updates the setting in the EEPROM. When the monitor is turn on again, the stored settings are used to set up the monitor for operation. What are the symptoms if the MONITOR or TVs EEPROM data is corrupted or damaged? No high voltage (no display). Horizontal or vertical frequencies run. Cannot save (store) current setting. satisfied control functions like sound, gifts and contrast control does not functioning. On Screen Display (OSD) does not function or the OSD have a corrupted display. High voltage shut down (EEPROM set the horizontal frequency way too low or twice the line frequency perhaps leading to failure of the horizontal output transistor (HOT)). What is an EEPROM programmer or copier? EEPROM seldom fail, they just lose or have their memory (data) corrupted may be due to high voltage and static discharge from a monitor. Once reprogrammed they are as good as new. As mentioned earlier, new EEPROMs are nil and need information or data to be loaded in order for it to functions. The job of copying the data into an EEPROM is done by a programmer or a copier. Programmers comes in all shapes and sizes. You can copy these devices for repair replacement only. You cannot copy them for resale without a letter of right from the vendor who produced them. There is quite a number of companies selling EEPROM programmer: - Typical EEPROM part no: - 24C02, 24C04, 24C08 etc 24C325, 24C645AT17C65, AT17C128 etc 93C06, 93C46, 93C56, 93C66 etc 25010, 25020, 25040 etc
|
Advice Home Business Technology Online Advertising Motivational Internet Marketing SEO Help Online Games Science Articles Happiness More Articles:1. The Future of Cell Phones Summary: While currently a cell phone camera may have limited capabilities, it's only a matter of time for it to exceed and surpass the performance of astand alobe video camera, although there is some concern over somebody being videotaped without their consent. Watching TV or movies - Provides live streaming television content for mobile phones. But that is just a matter of time. Cell phone carriers have truly embraced the multimedia revolution and decided to make our life cell phone centric. A… 2. The History of the Vacuum Cleaner: Perfection has taken a bit of time! Summary:The first vacuum cleaner is thought to have been created in the United States, in the mid 1800's. The motorized vacuum came to us about 1907 and has undergone major improvements and modifications to become the vacuum that we use today!Now, there are many, many vacuum cleaner manufacturers on the market. Article:The first vacuum cleaning agent is thought to have been created in the United States, in the mid 1800s. Today, the vacuum purifier is found in just near at hand every household i… 3. Get the most out of your digital camera today Summary: Whether you simply hit the shutter button to take pictures of your friends and family or if you want to have your camera with you at all times in order to capture the beauty of life wherever you find it, getting the most out of your digital camera can be easy. Your camera comes with a variety of quality settings to work with when taking images. Don't use TIFF, leave it on one of the medium quality level settings and your camera will take fine images for you and not eat up all your memor… 4. BIGSQUID RFID : Emerging to RFID Enterprise Solution Summary: The reader converts the radio waves reflected back from the RFID tag into digital information that can then be passed on to the computers that can make use of it.Objective The objective of any RFID system is to carry data in suitable transponders, generally known as tags, and to retrieve data, by machine-readable means, at a suitable time and place to satisfy particular application needs. They are classified within two frequency ranges, namely 125 KHz (low frequency) and 13.56 MHz (high… |
||||
